The carburetor is a mixer. It mixes gasoline from the tank with air 2,000 gallons of air with every gallon of gas. 化油器是一个混合器,它把来自油箱的汽油和空气加以混合,1加仑汽油混合2千加仑空气。
Empty out the gasoline from a tank. 把油箱里的汽油倒出来。
Please fill up my gasoline tank with lead free premium gas. 请加满油箱-无铅高级汽油。
Parameter Uncertainty Analysis of Sealed Gasoline Tank Leaking Pool Fire Risk Assessment 密闭汽油罐泄漏池火灾风险评估中的参数不确定性分析
The figures also affirm something we know every time we refill our gasoline tank. 每当我们在油箱里加油时,这些数字也会印证我们的一些认识。
There's a leak in the gasoline tank. 汽油箱有个裂缝。
Study on the Corrosion of Aluminum Floating Deck of Product Gasoline Tank 成品汽油罐铝浮盘腐蚀原因初探
According to the general tank cleaning method and principle stipulated in Safety Technical Regulations on the Cleaning of Oil Tanks, the specific method for cleaning the inner floating roof gasoline tank is summarized by practice. 按照《油罐清洗安全技术规程》所述的一般清罐方法和原则,通过清洗浅盘式内浮顶汽油罐,总结出清洗浅盘式内浮顶汽油罐的具体方法。
Research and Realization of Plastic Gasoline Tank Water-cooling Equipment Based on Solidworks 基于Solidworks的汽车塑料燃油箱水冷定型机的设计与实现
Corrosion Protection of Gasoline Tank 汽油储罐内壁防腐蚀经验
Analysis of the Fire and Explosion Quantitative Risk Assessment of the Gasoline Tank 汽油储罐火灾爆炸事故定量安全评价方法简析
It is considered that if the protective coating applies to the floating roof, the structure will be an ideal selection for the stabilized gasoline tank. 若对浮盘进行防腐处理,这种结构则是稳定汽油罐的理想选择。
To shorten the production cycle time and increase the output of automobile plastic gasoline tank, its cooling and solidification can be put on special fixture by wind or water after being taken from mold. 为缩短生产周期、提高产量,汽车塑料燃油箱的冷却定型可于开模后在定型架上采用风冷或水冷方式进行。
Design to Manual Operational Die of Drawstring of Gasoline Tank 油箱拉带手动模设计
Design on vibration test of the gasoline tank based on dynamics simulation 基于动力学仿真软件的油箱振动试验夹具设计
This thesis presents the whole perspective design of this equipment and software design project and implement condition. They establish the basis for studying the problem how to make full use of the fuel vapor in gasoline tank. 本文介绍了此装置的总体设计思路和硬、软件设计方案以及实施情况,为今后更进一步研究汽油箱内汽油蒸汽的充分利用问题奠定了基础。
Cleaning method for inner floating roof gasoline tank 浅盘式内浮顶汽油罐的清洗方法
Based on the above results, with the normal conditions and the same volume of tanks, the fuel evaporative pollutants control system of gasoline tank is basically fit for the methanol fuel tank. 试验结果表明,在正常条件下,油箱体积相同时,汽油箱燃油蒸发物吸附装置基本上适用于甲醇汽车。
Designs and studies of automobile gasoline tank occludent figuration machines 汽车油箱咬合成形机的设计
Cracks Analysis on Wainscot of Gasoline Tank 油箱壁板裂纹分析
Experimental study of burning characteristics in gasoline storage tank fires 汽油储罐火灾燃烧特性的实验研究
In the paper, we introduce the whole perspective and methodology of the gasoline tank pressure measuring and controlling system based on 8031, the paper also states the operation principle of the whole system, the key techniques in designing the hardware circuit and software. 本文介绍了基于8031单片机开发的汽油箱内汽油蒸汽压力测控系统的总体设计思路和方法,阐述了整个测控系统的工作原理、硬件和软件设计及相关技术问题。
The Application of the Self-decontaminating Gasoline Tank in Hydraulic and Lubricating System 自净化油箱在液压润滑系统中的应用
Modeling of airliner gasoline tank and modification of attitude error of sensor 民航客机油箱建模与油量传感器姿态误差修正
If the volume of carbon canister was increased by 28%, the working capacity of carbon canister used for methanol tank will be the same with that used for gasoline tank. 如果碳罐扩容28%,就能达到与汽油相同的吸附效果。
Corrosion failure analysis of aluminum alloy floats for a gasoline tank in oil storage factory 汽油罐铝合金浮筒失效分析浮筒式垂直升船机
Stabilized Gasoline Tank Matches Annular-cabin Type Steel Floating Roof 稳定汽油罐宜选用环舱式钢制内浮盘
The corrosion of the floating deck and barrel of the product gasoline tank in Fujian Refinery, the research testing and analysis of corrosion causes were discussed and solutions were presented. 阐述了炼油厂成品汽油罐铝浮盘及浮筒的腐蚀情况、腐蚀原因的试验研究及分析,提出了解决措施。
But most people don't attach more importance to the study on how to make full use of fuel vapor in the gasoline tank and decrease the pollution. 但在汽油箱内汽油蒸汽的节约利用,及减少其对环境的污染方面的研究,还未引起人们足够的重视。
Through the analysis of the previous technology for forming the end cap of the gasoline tank of light automobiles, a new forming technology was proposed. The structure and main design points of the die for this new technology were introduced 通过对轻型车油箱端盖原成形工艺的分析,提出了一种新的成形工艺,并介绍了其主要模具结构及设计要点